Bản in của bài viết

1.

Which of the following correctly describes ISDN BRI? (Choose three.) two 64 kbps B channels and one 16 kbps D channel B channel is suitable for voice data uses in-band signaling uses out-of-band signaling offers the equivalent of a T1/E1 connection twenty-three 64 kbps B channels and one 16 kbps D channel

2.

A network administrator in Europe has been asked to provide the network with an ISDN WAN link. The router available to provide the WAN connection is a non-modular Cisco router with an S/T interface. What further equipment will be provided by the ISDN service provider for the ISDN connection?
	Nothing. The router is already suitable.
	BRI WAN interface card to install in the router
	an external NT1 to terminate the local loop
	a TA/NT1 device to install on the router

3.

What must be configured for an ISDN PRI connection? (Choose three.)
	ISDN switch type
	Service Profile Identifier (SPID)
	Dial-on-Demand Routing (DDR)
	PRI group time slot
	T1/E1 controller, framing type and line coding

4.

A small company uses an ISDN WAN link to transfer e-mail to remote sites. What command would the administrator use to determine if the ISDN link is up?
	show isdn status
	show isdn active
	show dialer
	show interface bri0/0
	debug isdn active

5.

A network administrator is troubleshooting ISDN connectivity. The administrator suspects the problem lies with the authentication protocol. What command should the administrator use to view the authentication process between the router and the ISDN switch?
	debug pap authentication
	debug chap authentication
	debug ppp authentication
	debug isdn authentication

6.

The network administrator of XYZ company needs to configure a new ISDN router. After entering the commands shown in the graphic, the administrator tries to access the Internet but the ISDN connection does not open. If the service provider verifies that the problem is with XYZ's configuration, what is a possible cause of the problem? The dialer map is configured incorrectly. The encapsulation type is configured incorrectly. The dialer group is configured incorrectly. The ACL is configured incorrectly. The isdn switch-type command needs to be configured globally.

7.

Which of the following are true of ISDN routers configured with dialer profiles? (Choose two.)
	They do not use ACL to define interesting traffic.
	Their B channels can be configured with different subnets and encapsulation types.
	Their BRI interfaces can belong to multiple dialer pools.
	They use PPP only.
	They can only use the CHAP authentication protocol.

8.

Which of the following describes the use of a SPID? (Choose two.)
	selects the ISDN switch type
	identifies the line configuration of the BRI service
	allows multiple ISDN devices to share the local loop
	designates whether a device is a TE1 or TE2
	allows ISDN broadcasts

9.

Which of the following is considered out-of-band signaling?
	using a frequency outside of the rated bandwidth for transmission
	transmitting data over a control channel
	using a separate channel for control signals
	transmitting control signals over a data channel

10.

Why must routers be configured to specify the ISDN switch type?
	Switches use various implementations of Q.931.
	The IOS of most routers lacks the ability to autosense the switch.
	The switch must know what type of router it is communicating with.
	The Layer 3 connection between the terminal equipment and the ISDN switch is not standardized.

11.

Which command configures an ISDN interface to use a switch type which is different from that used on other interfaces on the router?
	Router(config)#switch-type switch-type
	Router(config-if)#switch-type switch-type
	Router(config)#isdn switch-type switch-type
	Router(config-if)#isdn switch-type switch-type

12.

Which router command would be used to enter the mode for configuring a T1 PRI connection?
	Router(config)# controller t1 {{slot/port}}
	Router(config)# interface pri t1 {{slot/port}}
	Router(config)# interface pri {{slot/port}} t1
	Router(config)# controller {{slot/port}} t1

13.

Which command is used within an existing ISDN network to display current call information, including the called number?
	show isdn status
	show isdn active
	show interfaces bri0/0
	show ip interfaces

14.

Which equipment should a customer purchase in order to connect to an ISDN BRI WAN service? (Choose two.)
	in the United States, a router with an ISDN BRI S/T interface
	in Europe, a router with an ISDN BRI S/T interface
	in the United States, a router with an ISDN BRI U interface
	in Europe, a router with an ISDN BRI U interface
	in the United States, a TE1 device attached to a router serial interface
	in Europe, a TE2 device attached to a router serial interface

15.

Which of the following protocols can be used to encapsulate data traffic sent from a router BRI interface? (Choose two.)
	Link Access Protocol - Data
	High-Level Data Link Control
	Logical Link Control
	Serial Data Link Control
	Point to Point protocol
	Binary Synchronous Control protocol

16.

Which of the following is essential for all ISDN BRI interface configurations?
	ISDN switch type
	line encoding technique
	line framing method
	local directory number
	service profile identifier

17.

What is a reason why static routes are preferred over dynamic routes for DDR to operate on an ISDN interface?
	An ISDN interface will not allow dynamic routing updates that use broadcast technology.
	A dynamic route will take precedence over a static route because of its lower administrative distance.
	Dynamic routing can never be considered interesting traffic by default.
	Dialer-list configuration does not support dynamic routing.
	Dynamic routes may cause the ISDN connection to dial constantly to transmit updates.

18.

A network administrator is troubleshooting an ISDN connectivity problem. Users are complaining they cannot connect to the Internet. The network administrator suspects the ISDN connection attempt is timing out before a connection can be established. What command would the network administrator use to determine what the "wait for carrier" timeout value is set to? show isdn status show isdn active show dialer show interfaces bri0/0 debug isdn q931 show ISDN interfaces