Bản in của bài viết

1.

How did Cisco alter the HDLC encapsulation to allow a single link to carry multiple protocols?
	split the transmissions into multiple channels each carrying a single protocol
	identified the protocol in the FCS field
	compressed the datagrams differently for each protocol
	added a type field to identify the protocol

2.

A technician has used Telnet to gain remote access to a router that has no connectivity on its serial interface. Which command should be issued to determine if the serial cable is connected properly?
	show controllers
	show processes
	show run
	show status

3.

A two router network is running PPP over the serial interfaces that connect them. The enable password on the Denim router is "gateway". The Denim router also has a locally configured authentication password for the Plaid router which is "fortress". Which command must be executed on the Plaid router to allow Denim to authenticate to the Plaid router using CHAP?
	Plaid(config)# enable secret gateway
	Plaid(config)# enable secret fortress
	Plaid(config)# username Plaid password fortress
	Plaid(config)# username Denim password fortress
	Plaid(config)# hostname Plaid secret password gateway
	Plaid(config)# hostname Plaid secret password fortress

4.

Which authentication protocol can be spoofed to allow playback attacks?
	MD5
	CHAP
	PAP
	NCP

5.

How is the MD5 function valuable in authentication? (Choose two.)
	uses a one-way hash function
	authentication occurs more rapidly
	challenges are unique
	the remote router assumes control of frequency of challenge
	the remote router assumes control of timing of challenge

6.

Which command specifies a link quality over a PPP link?
	ppp link 50
	ppp link quality 60
	ppp percentage 80
	ppp quality 90

7.

Refer to the output of the show interface Serial0/0 command in the graphic. How many NCPs have been established? 1 2 3 4

8.

A technician is testing the functionality of a recently installed router. The technician is unable to ping the serial interface of a remote router. The technician executes the show interface serial 0/0 command on the local router and receives the following output: Serial0/0 is up, line protocol is down(disabled) What are possible causes for this command output? (Choose two.)
	interface missing the no shutdown command
	clockrate command missing
	CSU/DSU failed
	interface shutdown due to high error rate
	cable missing

9.

When troubleshooting the Serial 0/0 interface of a router, a technician issues the show controllers command. The following was the output of the command: Interface is Serial0/0, electrical interface is UNKNOWN. What can be concluded about the Serial 0/0 interface? (Choose three.)
	Serial0/0 is down, line protocol is down
	Serial0/0 is down, line protocol is up
	Serial0/0 is up, line protocol is down
	The interface is neither DCE or DTE.
	The interface hardware may be faulty.
	The cabling may be improperly connected.

10.

Which of the following describe functions of the Point-to-Point protocol with regards to the OSI model? (Choose three.)
	PPP uses Layer 3 of the OSI model to establish and maintain a session between devices.
	PPP operates at all layers of the OSI model.
	PPP uses the data link layer to configure such options as error detection and compression.
	PPP provides a mechanism to multiplex several network layer protocols.
	PPP uses Network Control Protocols (NCP) to test and maintain connectivity between devices.
	PPP can be configured on both synchronous and asynchronous serial interfaces.

11.

PPP uses several protocols for communication. Which of the following are options that the LCP protocol in the PPP architecture can provide? (Choose two.)
	testing the quality of the link
	routing packets between devices
	assigning individual station addresses
	configuring network layer protocols
	negotiating authentication options

12.

Several tasks must occur before a link between two routers can pass data using PPP. Which of the following are required to establish and maintain a PPP session between two routers?
	configure each host with a PPP address
	configure authentication between the two routers
	send LCP and NCP frames to negotiate configuration parameters
	send hostname and password information between the two routers

13.

Which of the following is a reason for using such protocols as PAP and CHAP?
	to establish a PPP session
	to provide error checking on a WAN link
	to restrict access to networks connected by serial and ISDN links
	to provide a backup hostname and privilege mode password on the router

14.

What are three features of the CHAP protocol? (Choose three.)
	exchanges a random challenge number during the session to verify identity
	sends authentication password to verify identity
	prevents transmission of login information in plain text
	disconnects the PPP session if authentication fails
	initiates a two-way handshake

15.

Which command was used to display the partial output shown in the graphic? show ppp traffic show lcp traffic debug ppp negotiation debug ppp authentication

16.

What can be concluded from the output shown in the graphic? (Choose three.)
	A two-way handshake is occuring.
	The LCPs were already negotiated.
	The router can begin NCP negotiations.
	The debug ppp negotiation command was executed.
	The debug ppp authentication command was executed.

17.

Which advantage does the multilink option provide when using PPP?
	Data transmission has load balancing possibilities.
	Interfaces can be configured using both HDLC and PPP.
	More than one authentication method can be used.
	More than one compression protocol can be configured.