Bản in của bài viết

1.

Which ICMP message type notifies source hosts that a receiving host or network is not available?
	time exceeded
	redirect
	destination unreachable
	source quench
	parameter problem
	echo reply

2.

The network administrator shown in the exhibit can ping the E0 interface of the HAR router, but the telnet intranet.xyz.com command issued from the administrator's workstation fails to open a session with the intranet.xyz.com server. What are two possible causes of this problem? (Choose two.) upper-layer application problems domain name system problems IP addressing problems on the HAR router clock rate problems on the HAR router serial interface ICMP connectivity problems

3.

After issuing the show interfaces command, a technician notices the line "Serial1 is down, line protocol is down" in the output. Which of the following are possible reasons for this message output? (Choose three.)
	There is a mismatch in the encapsulation type on both ends of the link.
	A Layer 1 issue exists.
	An interface problem exists.
	The clockrate was not set during configuration.
	There is no usable media for the protocol.
	Keepalive messages are not being sent.

4.

After issuing the show interfaces serial1 command, an administrator notices an increasing number of carrier transitions. What are the possible causes for this increase? (Choose two.)
	There is an incorrect encapsulation configured on the interface.
	There could be an interruption in the line by the service provider.
	There is a faulty switch or CSU/DSU.
	There is noise on the serial line.

5.

When issuing the show interfaces serial1 command, a network administrator receives the output shown in the graphic. What are the possible causes of an increase in the number of input errors? (Choose three.)
	There could be Layer 3 addressing problems.
	There could be a problem with faulty telephone equipment.
	The router hardware could be defective.
	There is an incorrectly configured encapsulation on the interface.
	There could be a problem with the cabling.

6.

The show interfaces command provides line and protocol status information. Which of the following conditions would never occur in the output of this command?
	serial1 is up, line protocol is up
	serial1 is up, line protocol is down
	serial1 is down, line protocol is down
	serial1 is down, line protocol is up
	serial1 is administratively down, line protocol is down

7.

After issuing the command traceroute 192.168.4.2 from Router A, the following information is returned. Tracing the route to Router_D (192.168.4.2) 1 Router_B (192.168.2.2) 16 msec 16 msec 16 msec 2 * * * 3 * * * What can be concluded about the network shown in the graphic based on the output given? Network 192.168.5.0 is missing from the routing table on Router A. There is a problem with the connection between Router B and Router C. Router C is not running CDP. Some of the routers are non-Cisco devices. Router B was not able to return ICMP TEMs to Router A.

8.

A network administrator suspects that a network is not being included in the routing updates. Which command will provide information on when the next update is due and which networks are advertised in the update?
	Router# show interfaces
	Router# show controllers serial
	Router# show ip protocols
	Router# show ip route
	Router# show running-config

9.

Which two are true regarding the debug commands? (Choose two.)
	Debug commands may be issued from the user EXEC prompt.
	The command undebug all will turn off all debug operations.
	By default, the router sends the debug output and messages to the telnet session.
	The high processor overhead incurred using debug may disrupt normal router operation.
	The debug all command provides a summary view of router activity and can be used frequently for troubleshooting.
	The show debugging command will display current events such as traffic on an interface and error messages generated by nodes on the network.

10.

Which of the following lines from the show interfaces output would indicate a Layer 2 problem?
	Serial1 is up, line protocol is up.
	Serial1 is up, line protocol is down.
	Serial1 is down, line protocol is down.
	Serial1 is administratively down, line protocol is down.

11.

Which of the following would be the default administrative distance of a static IP route that references the IP address of the next hop?
	0
	1
	5
	20

12.

During the lookup process when forwarding a packet, a router checks its routing table for the best path to the destination. If a route has an administrative distance of 0, what does this indicate to the router?
	The packet should be discarded.
	The destination is unreachable.
	The destination is a directly connected network.
	The source of the update for that route is unreliable.

13.

Which command will display routing table information about all known networks and subnetworks?
	Router# show ip interfaces
	Router# show ip connections
	Router# show ip route
	Router# show ip networks

14.

Which of the following are advantages of using a static route? (Choose three.) secure operation highly adaptable low maintenance configuration low processor overhead precise control of path selection

15.

Consider the RIP network shown in the diagram. Which entries would be listed in the routing table of Router A?
	R 192.168.5.2[120/1] via 192.168.15.0, 00:00:09, Serial0
	R 192.168.15.0[120/1] via 192.168.5.2, 00:00:13, Serial1
	R 192.168.15.0[120/1] via 192.168.5.1, 00:00:13, Serial0
	R 192.168.5.1 [120/1] via 192.168.5.2 00:00:29, Serial1 R 192.168.15.0 [120/1] via 192.168.5.2, 00:00:29, Serial1
	R 192.168.5.1 [120/1] via 192.168.5.2 00:00:18, Serial0 R 192.168.15.2 [120/1] via 192.168.5.2, 00:00:18, Serial0

16.

Why does a router build a routing table? (Choose two.)
	to list available routes for forwarding data
	to map local Layer 2 addresses to the remote Layer 3 destination address
	to dynamically send periodic updates regarding the router's status
	to prevent routing loops when redundant links are added to the network
	to select the best path to a destination

17.

Which of the following commands can be used to statically configure default routes? (Choose two.)
	ip static-route
	ip route
	ip network-route
	ip default-network
	ip default-static

18.

Which command will verify the functionality of all seven layers of the OSI model on a network host?
	ping
	debug
	telnet
	traceroute

19.

Which items would be displayed when the show ip protocols command is executed? (Choose three.)
	sources of routing updates
	networks being advertised
	routing protocol up or down
	configured routed protocols
	Layer 2 status of the interface
	update timer values

20.

Which of the following is a problem at the physical layer of the OSI model?
	incorrect file formatting
	incorrect encapsulation on a serial interface
	incorrect routing protocol
	incorrect cable type

21.

Which three correctly pair a routing metric with its description? (Choose three.)
	hop count - the number of routers traversed to reach a destination
	bandwidth - the amount of time it takes a packet to travel a link
	load - the amount of activity on a link
	delay - the link speed
	reliability - the error rate on a link

22.

The network administrator is using a PC to access a router via the router console port. Both the PC and the router are powered on and a cable has been connected between them. However, a session cannot be established. Which steps might fix this problem? (Choose two.)
	Verify the cable is properly connected at each end.
	Reseat the network card in the PC.
	Verify the cable is the correct type.
	Verify that a password has been set on the console line.
	Check the transceiver for link lights.
	Reseat the console card on the router.

23.

A network technician has discovered that a router in the network can no longer be reached. The technician attempts to verify Layer 1 functionality, but is unable to physically inspect the cables. Which command can be used to determine the type of cable connected to the router?
	Router# show interfaces
	Router# show controllers serial
	Router# show ip route
	Router# show ip protocol
	Router# show version
	Router# show running-config

24.

When the show cdp neighbors command is issued from Router C, which devices will be displayed in the output? D, SWH-2 A, B, D SWH-1, SWH-2 B, D SWH-1, A, B A, B, D, SWH-1, SWH-2