Bản in của bài viết

Click vào đây để xem bài viết này ở định dạng ban đầu

lehuy0305's Blog

Module1_S3

1.

Which of the following is considered a limitation of RIP v1?

RIP v1 does not send subnet mask information in its updates.

RIP v1 is not widely supported by networking hardware vendors.

RIP v1 consumes excessive bandwidth by multicasting routing updates using a Class D address.

RIP v1 requires enhanced router processors and extra RAM to function effectively.

RIP v1 does not support load balancing across equal-cost paths.

RIP v1 authentication is complicated and time-consuming to configure.
2.

Which of the following statements are true regarding RIP v1 and v2? (Choose three.)
	Both RIP versions use hop count.
	Both RIP versions can provide authentication of update sources.
	Both RIP versions use 16 hops as a metric for infinite distance.
	RIP v1 uses split horizon to prevent routing loops while RIP v2 does not.
	RIP v1 uses hold-down times to prevent routing loops while RIP v2 does not.
	RIP v1 broadcasts routing table updates, while RIP v2 multicasts its updates.

A new network is to be configured on a router. Which of the following tasks must be completed to configure this interface and implement dynamic IP routing for the new network? (Choose three.)
	Select the routing protocol to be configured.
	Assign an IP address and subnet mask to the interface.
	Update the ip host configuration information with the device name and new interface IP address.
	Configure the routing protocol with the new network IP address.
	Configure the routing protocol with the new interface IP address and subnet mask.
	Configure the routing protocol in use on all other enterprise routers with the new network information.

Router1 and Router2 shown in the topology have been configured with the no ip subnet-zero command. Which of the following valid VLSM network numbers could be used for the serial link between Router1 and Router2? (Choose two.)
	192.168.1.0/30
	192.168.1.4/30
	192.168.1.8/30
	192.168.1.96/30
	192.168.1.138/30
	192.168.1.190/30

Which command would a network administrator use to determine if the routers in an enterprise have learned about a newly added network?
	router# show ip address
	router# show ip route
	router# show ip networks
	router# show ip interface brief
	router# debug ip protocol
	router# debug rip update

How does a router know of paths to destination networks? (Choose two.)
	inspection of the destination IP address in data packets
	ARP requests from connected routers
	manual configuration of routes
	updates from other routers
	DHCP information broadcasts
	updates from the SMTP management information base

Refer to the network shown. How will Router1 summarize and advertise the four networks attached to its Ethernet ports?
	172.16.16.0/20
	172.16.19.0/20
	172.16.16.0/20 and 172.16.19.0/20
	172.16.16.0/22
	172.16.18.0/24
	172.16.0.0/24

In the network shown in the graphic, three bits were borrowed from the host portion of a Class C address. How many valid host addresses will be unused on the three point-to-point links combined if VLSM is not used?
	3
	4
	12
	36
	84
	180

10.

How often does RIP v1 send routing table updates, by default?
	every 30 seconds
	every 45 seconds
	every 60 seconds
	every 90 seconds

11.

What is the default network mask for a Class B address?
	255.0.0.0
	255.255.0.0
	255.255.255.0
	255.255.255.255

12.

Which subnet mask is represented by the /21 notation?
	255.255.224.0
	255.255.248.0
	255.255.252.0
	255.255.240.0

13.

Which of the following are contained in the routing updates of classless routing protocols? (Choose two.)
	32-bit address
	next hop router interface
	subnet mask
	unicast host address
	Layer 2 address

14.

What is the purpose of the network command used in the configuration of the RIP routing protocol?
	It specifies RIP v2 as the routing protocol.
	It enables the use of VLSM.
	It specifies the fastest path to the destination route.
	It specifies which interfaces will exchange RIP routing updates.
	It activates RIP for all routes that exist within the enterprise network.

15.

Which of the following problems does VLSM help to alleviate?
	the shortage of IP addresses
	the difficulty of assigning static IP addresses to hosts in large enterprises
	the complexity of implementing advanced routing protocols such as OSPF and EIGRP
	the shortage of network administrators qualified in the use of RIP v1 and IGRP

16.

What does VLSM allow a network administrator to do?
	utilize one subnet mask throughout an autonomous system
	utilize multiple subnet masks in the same IP address space
	utilize IGRP as the routing protocol in an entire autonomous system
	utilize multiple routing protocols within an autonomous system

17.

A Class C network address has been subnetted into eight subnetworks. Using VLSM, the last subnet will be divided into eight smaller subnetworks. What bit mask must be used to create eight smaller subnetworks, each having two usable host addresses?
	/26
	/27
	/28
	/29
	/30
	/31

18.

An additional subnet is required for a new Ethernet link between Router1 and Router2 as shown in the diagram. Which of the following subnet addresses can be configured in this network to provide a maximum of 14 useable addresses for this link while wasting the fewest addresses?
	192.1.1.16/26
	192.1.1.96/28
	192.1.1.160/28
	192.1.1.196/27
	192.1.1.224/28
	192.1.1.240/28

19.

The network shown in the diagram is having problems routing traffic. It is suspected that the problem is with the addressing scheme. What is the problem with the addressing used in the topology?
	The address assigned to the Ethernet0 interface of Router1 is a broadcast address for that subnetwork.
	The subnetwork configured on the serial link between Router1 and Router2 overlaps with the subnetwork assigned to Ethernet0 of Router3.
	The subnetwork assigned to the Serial0 interface of Router1 is on a different subnetwork from the address for Serial0 of Router2.
	The subnetwork assigned to Ethernet0 of Router2 overlaps with the subnetwork assigned to Ethernet0 of Router3.

20.