Module2_s2

 Câu 1:

Which of the following is the correct flow of routines for a router startup?
	load bootstrap, load IOS, apply configuration
	load bootstrap, apply configuration, load IOS
	load IOS, load bootstrap, apply configuration, check hardware
	check hardware, apply configuration, load bootstrap, load IOS

 Câu 2:

Under what conditions does the router enter setup mode? (Choose three.)
	immediately after issuing the command Router#erase start
	after issuing the command Router#setup
	during the initial configuration of a router
	after deleting the backup configuration and reloading the router
	after deleting the running configuration

 Câu 3:

Which of the following identifies the correct items needed to initially configure a router? 1) DB-9-to-RJ-45 on the PC's serial port 2) a straight through cable 3) the router's console port 1) PC's Ethernet port 2) a crossover cable 3) the router's Ethernet port 1) DB-9-to-RJ-45 on the PC's serial port 2) a rollover cable 3) the router's Ethernet port 1) PC's Ethernet port 2) a rollover cable 3) the router's console port 1) DB-9-to-RJ-45 on the PC's serial port 2) a rollover cable 3) the router's console port 1) PC's Ethernet port 2) a rollover cable 3) the router's Ethernet port

 Câu 4:

What is the default sequence for loading the configuration file?
	NVRAM, FLASH, ROM
	FLASH, TFTP,CONSOLE
	NVRAM, TFTP, CONSOLE
	FLASH, TFTP, ROM

 Câu 5:

What does the command sh? return as output if issued at the Router# prompt?
	all show commands allowed in privileged mode
	all commands beginning with the letters sh
	an incomplete command error message
	an invalid command error message

 Câu 6:

Which keystroke is used to move to the beginning of a command line?
	Ctrl-A
	Ctrl-B
	Esc-A
	Esc-B
	Ctrl-C
	Ctrl-Z

 Câu 7:

A network administrator needs to configure a router. Which of the following connection methods requires network functionality to be accessible?
	console
	AUX
	Telnet
	modem

 Câu 8:

Which keystrokes can be used to return to the privileged mode from the interface configuration mode?
	Ctrl-P
	Ctrl-Shift-6, then X
	Ctrl-Z
	Esc

 Câu 9:

Cisco IOS software is separated into two levels as a security feature. What are those two levels? (Choose two.)
	global
	privileged
	local
	user
	interface

 Câu 10:

Which connection method can be used to perform the initial configuration of a router?
	use a serial connection of a computer connected to the console port of a router
	telnet to the router through a serial port
	use a vty port through the Ethernet interface
	use a modem connected to the AUX port of the router

 Câu 11:

Which of the following statements concerning router interface modes are correct? (Choose three.) User EXEC mode provides commands to monitor router operation. Privileged EXEC mode only provides commands to change or configure router operation. Password protected configuration modes can be accessed from either user EXEC or privileged EXEC modes. On a router with the name Core1, the prompt indicating privileged EXEC mode is Core1#. The command to enter privileged EXEC mode is Router# enable. A username and password may be required to enter privileged EXEC mode.

 Câu 12:

What information does the name of the IOS file provide to the network administrator? (Choose three.)
	the amount of NVRAM required to run the image
	the hardware platform the image runs on
	the various software platforms the image can run on
	special features and capabilities of the image
	the bandwidth supported by the IOS
	where the image executes from and if it has been compressed

 Câu 13:

What baud rate needs to be configured on terminal emulation software to allow a connection to the console port of a router?
	2400
	4800
	9600
	14200
	38400

 Câu 14:

Which tasks can be accomplished by using the command history feature? (Choose two.)
	View a list of commands entered in a previous session.
	Recall up to 15 command lines by default.
	Set the command history buffer size.
	Recall previously entered commands.
	Save command lines in a log file for future reference

 Câu 15:

When the router output is being viewed through a terminal program, which statements are true regarding the --More-- prompt at the bottom of the router display? (Choose two.)
	Press the Spacebar to display the next line.
	Press the Spacebar to view the next screen.
	Press the PgDn key to view the next screen.
	Press the Enter key to display the next line.
	Press the Enter key to view the next screen.

 Câu 16:

Which command takes precedence if the commands enable password and enable secret are both configured on a router?
	enable password
	enable secret
	Neither. They are both enabled.
	Neither. They cancel each other out.

 Câu 17:

What information about the router and its startup process can be gathered from the output of the show version command? (Choose three.)
	the last restart method
	the command buffer contents
	the amount of NVRAM and FLASH used
	the configuration register settings
	the location from where the IOS loaded

 Câu 18:

After the active IOS image has been loaded into RAM from flash memory, which commands could be used to display the file name of the active IOS? (Choose two.)
	Router# show IOS
	Router# show flash
	Router# show nvram
	Router# show version
	Router# show startup-config
	Router# show running-config

 Câu 19:

Which tasks can be performed in the ROM monitor mode? (Choose two.)
	recover from system failures
	create startup configuration files
	recover from lost passwords
	configure IP addresses on all router interfaces
	perform high level diagnostics